Guide

Compression: how the parts fit together

Compression is the set of parts that holds the handlebar (the bar) and the fork together. It comes in three kinds: SCS, HIC and IHC. They cannot be mixed freely.

If you bought a complete scooter, its parts already fit together. This page only matters when you buy loose parts.

My scooter

Choose your scooter once. Then the page of every fork, bar and clamp tells you whether the part fits it.

What do you ride?

Choose your system

Start with the fork. It decides which bar and clamp you need.

Drawing of a stunt scooter from the side: the bar at the top, the fork’s compression tube inside the bar, the clamp, the headset, the fork with the front wheel, and the deck with the rear wheel.

Does it fit together?

Find your fork and see whether your bar fits.

Fork Standard bar 28 mm inside Oversized bar 32 mm inside
SCS Fits Use an SCS clamp. Fits Use an SCS clamp.
HIC Does not fit Choose an oversized bar (32 mm inside).Oversized bars (32 mm inside) – for HIC and SCS Fits The bar must have a slit.
IHC Fits The bar must have a slit. Does not fit Fix: an IHC to HIC converter. Or choose a standard bar (28 mm inside).Standard bars (28 mm inside) – for IHC and SCS

If your fork takes several systems, for example SCS/HIC, it is enough that one of them fits the bar. The clamp must then match that system: SCS needs an SCS clamp.

IHC fork and oversized bar?

You can keep your bar. An IHC to HIC converter goes over the compression tube of the fork and makes the bar fit.

Keep your bar – this part makes it fit:

The 3 most common mistakes

  1. An oversized (thick) bar on an IHC fork. Fix: an IHC to HIC converter. Or choose a standard bar (28 mm inside).
  2. A standard bar on a HIC fork. Choose an oversized bar (32 mm inside).
  3. A clamp that does not match the outside diameter of the bar. Choose a 32 or 35 mm clamp to match the bar. Or choose a clamp with a shim.
The words in short
Bar
The handlebar.
Fork
The part that holds the front wheel.
Clamp
The ring that squeezes the bar onto the fork.
Shim
Comes with some clamps, so the clamp fits bars of both 32 and 35 mm outside.
Slit
A cut at the bottom of the bar.
Quick overview
PartMust matchWhat to check
Bar The system of the fork, and the clamp. Inside diameter: 28 or 32 mm. Outside diameter: 32 or 35 mm. Whether the bar has a slit.
Fork The system. SCS, HIC or IHC.
Clamp The outside diameter of the bar, and the system. 32 or 35 mm. For SCS it must be an SCS clamp.
Sizes and tolerances

Bar

Inside diameter Decides whether the bar fits over the fork.
Standard28 mm
Oversized32 mm
Outside diameter The clamp must match the outside diameter of the bar, unless it has a shim.
Standard32 mm
Oversized35 mm

Wheels

The most common wheel sizes.
TypeDiameterHub width
Standard wheels100, 110 or 120 mm24 mm
Wide hub110, 115 or 120 mm30 mm
  • The axle hole of the fork (usually 8 mm) must match the bearings of the wheel.
  • The wheel must not rub against the fork.
  • 30 mm wide wheels need specific forks and spacers.
  • The deck decides how large your wheels can be.
  • Griptape: the difference in width between griptape and deck should be under 5 mm. If the griptape is wider, you trim it.

Common questions

What is compression?

The parts that hold the fork, deck and bar together. With the wrong choice the scooter cannot be assembled.

How do I see which system my scooter has?

Look at the product page of your scooter or your fork. In our shop the system is in the name of the fork, for example SCS/HIC. If in doubt, ask customer service.

Can I mix the systems?

Not freely. A compression part must have the same system as the fork. Some forks take several systems, and then one shared system is enough.

What if I buy the wrong part?

You have 365 days to return it.

We check for you

Put your parts in the cart. If we can see that two parts do not fit together, the cart says so and suggests parts that do.